46x46x24 acrylic
Hello all,
I am new to this site and to building my own tanks but not to saltwater. I have bought Joey's book which led me to this site. I'm curious to what everyone thinks good and bad about my upcoming build. It will be placed in wall on a corner so it will be viewable from three sides. The back of the tank will be accessible from the stair well going to the basement. I am bouncing all over the place on different pump sizes and what not. I am still trying to determine what size sump to build and types of filtration. In the past i used a refugium and a skimmer although i like the idea of the fluidized method. I am going to be using the solderless leds that joey used in a build. It will be a reef tank. Thanks Josh |
Really no imput
|
I mean, you didn't really ask a question. Just made some statements. What input would you like?
|
That size tank is sort of ambitious for a first time build. Either way, with some good practice, and a second or 3rd set of hands it could probably be done. Not easy, but it can be done.
Corey |
That would be a great size. Good luck.
|
Sorry, who's Joey? My general advice to anyone contemplating a reef tank is to lie down until the feeling goes away.
|
I have had tanks forever and after getting started in saltwater, I swore I would never have another plastic tank for reefing - too hard to keep clean, glass is sooo much better.
Cheers! and good luck |
I wouldn't trade my acrylic tank for glass ever. 3.5 years or so and going great. Sure it has a few scratches, but I can buff them out if I want to.
Corey |
Quote:
|
Oh ok, thx. I don't watch YouTube Reef tank videos just as a matter of principle - too many knuckleheads parading as experts.
|
I have had acrylic tanks in the past up to 200 gallons and they are nice but they do scratch easily and tend to bow if they are real long (I had one that was 7'). You can remove scratches to a point but it is never like new. Having said that I have built a few glass tanks and after taking a tour of a company that builds acrylic tanks I can say I would never attempt it. Getting the seams right is not for the faint of heart and polishing the edges is also not easy. I saw it done using a flame. With a glass tank you order the glass with polished edges and if you mess up a seam you can take off panel and try it again.
|
Quote:
He presents as a very charismatic figure on youtube. That's about the most positive thing I could say about him. The danger is that he presents himself as an expert but promotes half-baked ideas. |
Thanks for all the replies. YA i was referring to the youtube guy. The only diy thing i'm going to do is the tank and maybe the sump. Glass is heavy and can break when hit. Being that this is going into a wall in the center of the house :I don't want something that could break around by kids. The question that i meant to ask was would would you guys recommend for pump, sump, and overflow sizing. I have done reef before a 60 and a 75 all glass setups both with sumps. I just ordered the first part of the setup and that was a 5 stage rodi from bulk reef. getting the parts as i get cash. The other thing about acrylic is i can get 5/8 for about 900 and 3/4 for 1100. I can not find a place to get bulk large size glass plus with a tank that size I am a little leary about siliconing it together. That is a lot of water and pressure. i mean I want a 24-28 inch water level. I want to use rapid led lighting ut i also need to keep the price down until i'm ready to put lps in.
|
Im going to chime in here and give you my thoughts. Others may not agree. With my skill level this works for me. Maybe not everyone. If I am working with 1/2" or less cast acrylic, I find the pin method works just fine. A lot of practice is needed to make good bubble free tight seams. I will say this again. A lot of practice is needed .... A bit harder the longer the seams but I can do it. I can also route up to 1/2" just fine with what I have in my garage shop. This makes for great seams. I have found I am not so good at cutting and keeping things square. Lots of guides and clamps make it possible.
Anything over 1/2" I have the plastic supplier cut and then route it on their CNC machine. Costs more but the end product is better than what I am capable of doing. I use the pin method and weld-on #4, on everything under 1/2 inch. You can search for some treads about this. Experts cover what they have done to perfect the method. Some even have pictures of layup with shims, overlap for the fillet ect....It works. Thicker than 1/2 inch I have been using weld-on #40. Its 2 part and takes some getting use to. Pieces need to be held in place at 90 degrees with a 1mm gap, back side taped and then tilted so you can get the stuff to run into and fill the seam. Takes a lot of practice and the stuff is not cheap nor avail everywhere. Pumps. Depends on your overflow. If its a Bean Animal I would do 1-1/2 inch drain pipes and a pump that can put out somewhere around 2500 gph. This will work if you are going to use powers heads for most of your circulation. Sump size. Bigger is better, really depends on what in the sump, skimmer ect...and I will leave it at that. These are just ball park things, not knowing what you plan to keep, its hard to make the call. |
Lapin, so if i get this right i have to use the in method as well as use weld on 40 and tilt the panel to apply the solvent and then place it back at 90 and then remove the pins. Or do i just tilt the panel and apply the solvent and tip it back to 90. The King of DIY made it seem so easy. This is starting to seem harder. But i work in custom fab and my neighbor has a wood shop with a router and a huge table saw and a plywood saw.
|
I can't wait to hear how this turns out.
|
1 Attachment(s)
I normally dont use both on the same project.
I use the pin method and weld-on #4, on everything under 1/2 inch.(solvent, thin like water, used with pin method by me) Lots of videos and info on this on line. Some dont use pins, making it very simple. I would not trust my joints if I did this. I feel you need a little space for the first 10 to 20 seconds to allow enough solvent to soften the joint before pulling the pins. Thicker than 1/2 inch I have been using weld-on #40. ( 2 part, kinda like liquid resin for casting. Needs 1mm gap between pieces for it to flow into. The stuff will flow into the joint a lot better if you angle the pieces) You leave it at an angle until cured before moving on to the next panel This is one of many good links. Weld-on #4 method plus assembly order. https://www.professionalplastics.com...nAquarium2.pdf |
ok now i understand, but what do you use for the 1mm gap. I will be over 1/2 inch no matter what so I will be sticking the #40 and that method. Unless i can find a place to purchase glass at a good price.
|
ok that link you posted tells me that i can use 1/2 if i keep the height at 24". Now i assume that is water line, or i hope so anyways. I had been following manufacture specs before and thought that it was a little much. Of course i am euro bracing the tank.
|
Quote:
|
Oh and my plan is a mixed tank but not really going to get into sps. mostly leathers and lps and fish.
|
Quote:
Its just 1 type of overflow configuration for a tank like the "durso" is. |
Quote:
|
I see that would be an ideal set up. Space really isnt going to be an issue. What size acrylic would you use for a 24" water line?
|
Quote:
|
All times are GMT -6. The time now is 01:42 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
User Alert System provided by
Advanced User Tagging v3.3.0 (Pro) -
vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.