|
09/12/2019, 02:24 PM | #1 |
Registered Member
Join Date: Oct 2016
Posts: 22
|
How to connect Kessil A360w LED Chip
Hi ,
I have a dead light , that i have stripped down. I do think that the LED chip is ok , but dont know how to test it. There is 10 cables to the chip , four black two bown four black. Dont know what V or A to what cables =) And of course Kessil said to me that it is confidential , so no help from them.... So IŽll try to reach out to the community for some help instead. |
09/12/2019, 06:00 PM | #2 |
Registered Member
Join Date: Sep 2003
Location: North Carolina
Posts: 20,050
|
Got a multimeter?
Got a constant current benchtop power supply? Can you take some detailed pictures?
__________________
Who me? |
09/12/2019, 07:40 PM | #3 |
Registered Member
Join Date: Oct 2016
Posts: 22
|
Yes I have a multimeter , and also a constant current power supply.
|
09/13/2019, 07:55 AM | #4 |
Registered Member
Join Date: Sep 2003
Location: North Carolina
Posts: 20,050
|
An adjustable CC supply?
Pictures? Tried probing the pins with the diode test function of the meter? Got a table of the results? Named the wires for identification? ,etc...
__________________
Who me? |
09/13/2019, 08:27 AM | #5 |
Registered Member
Join Date: Jan 2015
Location: Fremont, CA
Posts: 9,555
|
I got two of those and the chips in them should be good.
Following along... Sent from my XT1254 using Tapatalk
__________________
Pairs: 4 percula, 3 P. kauderni, 3 D. excisus, 1 ea of P. diacanthus, S. splendidus, C. altivelis O. rosenblatti, D. janssi, S. yasha & a Gramma loreto trio 3 P. diacanthus. 2 C. starcki Current Tank Info: 200 gal 4 tank system (40x28x24 + 40B + 40B sump tank + 20g refugium) + 30x18x18 mixed reef + 20g East Pacific biotop + 20g FW +... |
09/13/2019, 11:53 AM | #6 |
Registered Member
Join Date: Oct 2016
Posts: 22
|
|
09/13/2019, 11:59 AM | #7 |
Registered Member
Join Date: Oct 2016
Posts: 22
|
I have not tried to probe the cales for results yet.
A bit out of my area , i guess=) , but i will try it later and see if i can understand something from it. |
09/13/2019, 12:16 PM | #8 |
Registered Member
Join Date: Sep 2003
Location: North Carolina
Posts: 20,050
|
Can you give us photos of where the wires connect and more?
Take like 20 pictures of various parts.. We can trace down what goes to what and potentially help.. The more data you can give us the better your chances..
__________________
Who me? |
09/13/2019, 12:21 PM | #9 |
Registered Member
Join Date: Sep 2003
Location: North Carolina
Posts: 20,050
|
And of course did you already check to make sure the adapter (power supply) is outputting what it should be?
I think they are 19VDC supplies.. 4.7A
__________________
Who me? |
09/13/2019, 12:39 PM | #10 |
Registered Member
Join Date: Oct 2016
Posts: 22
|
More photos in the link above now.
The power supply was the first thing i suspected , because i measured zero V from it. But the problem was it was in protection mode due to short circuit. So the main problem is a short circuit in the main board , and since i`m no technician , i gave up. Now i just try to save the LED chip for some project- |
09/13/2019, 02:19 PM | #11 |
Registered Member
Join Date: Sep 2003
Location: North Carolina
Posts: 20,050
|
Did you already post this on the other reef 2 reef forum
D2 certainly looks burnt
__________________
Who me? |
09/13/2019, 03:16 PM | #12 |
Registered Member
Join Date: Oct 2016
Posts: 22
|
Nope , first post about it.
Sounds familiar with another post I've read some time ago. But like I've said before , i have given up the hope for the other stuff , just into the chip right now 😅 |
|
|