|
06/08/2009, 06:34 PM | #1 |
Registered Member
Join Date: Jun 2004
Location: ON Canada
Posts: 142
|
WWD flashing Red
I just installed the mp40w tonight and the pump starts up and runs for a few seconds and then the driver just flashes red. Nothing in the book tells you what a red flash is. Please help
|
06/08/2009, 07:23 PM | #2 |
Registered Member
Join Date: May 2008
Location: Willard, Oh
Posts: 656
|
Hold down mode (pump blinks white)
Hold down mode/set (pump blinks yellow/white) Cycle power to the pump by unplugging and replugging it in. Somehow you programmed the pump's calibration sequence for auto-disconnect while the pump was attached to the tank and this is the result. The pump must be run in your hand for the auto-disconnect calibration sequence or else this will happen every time. The process above will clear out the calibration.
__________________
Sean Current Tank Info: 120 gal 30 gal sump/fuge, ATB Econo 840 skimmer, 2 Vortech MP40w, AC Jr., 2-250watt MH 20K Radiums, Lumen Max 2 reflectors, 2 tek T5 retro actinic, Prime chiller, ATO/kalk reactor, drews dosers on two part. |
06/08/2009, 08:43 PM | #3 |
Registered Member
Join Date: Jun 2004
Location: ON Canada
Posts: 142
|
Thanks Surge.
Up and running!! |
06/09/2009, 01:24 PM | #4 |
RC Sponsor
Join Date: Sep 2005
Location: Allentown, PA
Posts: 4,870
|
Thanks for helping, surge.
__________________
Tim Marks President EcoTech Marine www.ecotechmarine.com If the above information doesn't help you, please contact us at 1-800-785-0338 ext. 2 or by e-mailing [email]support@ecotech |
06/09/2009, 08:26 PM | #5 |
Registered Member
Join Date: Jun 2004
Location: ON Canada
Posts: 142
|
Pump ran great last night. Second pump has been running for 4 days now with no problems. Now this pump is flashing red/yellow. I have tried to unplug it and and plug back in and it won't stay running. Alignment is good and the motor is not hot. I have it running slave to the other on yellow setting. Any help now?
|
06/10/2009, 09:26 AM | #6 |
RC Sponsor
Join Date: Sep 2005
Location: Allentown, PA
Posts: 4,870
|
Hi reeflover-
Give Steve a call at 610.954.8480 ext 106 and he can walk you through the basic things to look for with that error code. There's also more info here: http://ecotechmarine.com/faq/trouble...odes-indicate/
__________________
Tim Marks President EcoTech Marine www.ecotechmarine.com If the above information doesn't help you, please contact us at 1-800-785-0338 ext. 2 or by e-mailing [email]support@ecotech |
06/10/2009, 03:39 PM | #7 |
Registered Member
Join Date: Jun 2004
Location: ON Canada
Posts: 142
|
It is flashing red/orange. I took a closer look at that is the colours. Do I need to send this pump back?
|
06/10/2009, 11:23 PM | #8 | |
Registered Member
Join Date: Jun 2007
Location: Bakersfield, CA
Posts: 118
|
Quote:
Should be in the user manual for sure!!! |
|
06/11/2009, 09:16 AM | #9 |
RC Sponsor
Join Date: Sep 2005
Location: Allentown, PA
Posts: 4,870
|
__________________
Tim Marks President EcoTech Marine www.ecotechmarine.com If the above information doesn't help you, please contact us at 1-800-785-0338 ext. 2 or by e-mailing [email]support@ecotech |
Thread Tools | |
|
|