Reef Central Online Community

Go Back   Reef Central Online Community > General Interest Forums > Do It Yourself
Blogs FAQ Calendar Mark Forums Read

Notices

User Tag List

Reply
Thread Tools
Unread 05/20/2019, 11:14 AM   #1
mr9iron
15& Over Club
 
mr9iron's Avatar
 
Join Date: Feb 2001
Location: Missouri
Posts: 2,552
Blog Entries: 1
Bean Animal good need help

I purchased a Modular Marine 1200 gph overflow that has 3/4 uniseals on the external box to go to the sump.

I ran 3/4 pipe from the box about 8 inches down then coupled it to 1 inch plumbing and immediately installed the gate valve. The gate valve sits about 2 feet above the sump.

The weir is connected via 1 inch bulkheads that go to the external box and flow through the above mentioned pipe.

I cannot get enough flow through the weir to balance the Bean Animal.

I am using a Vectra L1 pump on a 93 gallon cube and it is returned via 1 inch plumbing with a couple of tees, 90s and a manifold.

Should I:
1. Install the gate valve at the sump so that the 1 inch pipe fills up and I can better adjust it. As it is now because of the increase of pipe size and the height of my gate valve I don’t think the 1 inch pipe is able to get a full siphon going.

Or:
2. Rip out all of my plumbing and go 3/4.




Sent from my iPhone using Tapatalk


__________________
Vince
______________________________

Current Tank Info: Frag tank at the moment, planning another
mr9iron is offline   Reply With Quote
Unread 05/20/2019, 12:15 PM   #2
mcgyvr
Registered Member
 
mcgyvr's Avatar
 
Join Date: Sep 2003
Location: North Carolina
Posts: 20,050
Quote:
Originally Posted by mr9iron View Post
I cannot get enough flow through the weir to balance the Bean Animal.
Can you be very specific about exactly what is happening?
Bubbles/gulping at secondary?
Sucking inside external box due to low water level?

It can take some time for a drain setup to reach equilibrium when first started up..

You may need to close the valve on the primary 50% or more..


__________________
Who me?
mcgyvr is offline   Reply With Quote
Unread 05/20/2019, 06:32 PM   #3
mr9iron
15& Over Club
 
mr9iron's Avatar
 
Join Date: Feb 2001
Location: Missouri
Posts: 2,552
Blog Entries: 1
When I put the wier on the water in the tank rises so high that it almost overflows the tank.

The water level in the rear box drops and it just makes a really loud sucking/gurgling sound.

The bulkheads that attach to the rear box are 1 inch. However, the wier is auction fit and is reduced with 3/4 pvc.

I can’t figure out how to attach a video or I would.


Sent from my iPhone using Tapatalk


__________________
Vince
______________________________

Current Tank Info: Frag tank at the moment, planning another
mr9iron is offline   Reply With Quote
Unread 05/20/2019, 06:37 PM   #4
mr9iron
15& Over Club
 
mr9iron's Avatar
 
Join Date: Feb 2001
Location: Missouri
Posts: 2,552
Blog Entries: 1
Here is a link to the video I posted on YouTube. You really cannot hear me explaining the problem but you will see what happens.

https://youtu.be/-GpEzQdfplY


Sent from my iPhone using Tapatalk


__________________
Vince
______________________________

Current Tank Info: Frag tank at the moment, planning another
mr9iron is offline   Reply With Quote
Unread 05/20/2019, 07:14 PM   #5
on the spot
Registered Member
 
Join Date: Oct 2007
Location: West Michigan
Posts: 1,010
@1:16 - the plumbing inside the drain box looks wanky - what's going on in there?

It looks like you have three open channels.


on the spot is offline   Reply With Quote
Unread 05/20/2019, 07:23 PM   #6
mr9iron
15& Over Club
 
mr9iron's Avatar
 
Join Date: Feb 2001
Location: Missouri
Posts: 2,552
Blog Entries: 1
Quote:
Originally Posted by on the spot View Post
@1:16 - the plumbing inside the drain box looks wanky - what's going on in there?



It looks like you have three open channels.


I’ve got an open channel, an emergency drain and the middle I was just playing around with. Even with a raised 90 it does the same thing.


Sent from my iPhone using Tapatalk


__________________
Vince
______________________________

Current Tank Info: Frag tank at the moment, planning another
mr9iron is offline   Reply With Quote
Unread 05/20/2019, 07:24 PM   #7
mr9iron
15& Over Club
 
mr9iron's Avatar
 
Join Date: Feb 2001
Location: Missouri
Posts: 2,552
Blog Entries: 1
Quote:
Originally Posted by mr9iron View Post
I’ve got an open channel, an emergency drain and the middle I was just playing around with. Even with a raised 90 it does the same thing.


Sent from my iPhone using Tapatalk


The secondary drain that is.


Sent from my iPhone using Tapatalk


__________________
Vince
______________________________

Current Tank Info: Frag tank at the moment, planning another
mr9iron is offline   Reply With Quote
Unread 05/20/2019, 07:53 PM   #8
mcgyvr
Registered Member
 
mcgyvr's Avatar
 
Join Date: Sep 2003
Location: North Carolina
Posts: 20,050
Close valve more..thats it


__________________
Who me?
mcgyvr is offline   Reply With Quote
Unread 05/21/2019, 04:21 AM   #9
mr9iron
15& Over Club
 
mr9iron's Avatar
 
Join Date: Feb 2001
Location: Missouri
Posts: 2,552
Blog Entries: 1
Quote:
Originally Posted by mcgyvr View Post
Close valve more..thats it


When I do that it causes my tank to overflow.


Sent from my iPhone using Tapatalk


__________________
Vince
______________________________

Current Tank Info: Frag tank at the moment, planning another
mr9iron is offline   Reply With Quote
Unread 05/21/2019, 07:12 AM   #10
jphayes921
Registered Member
 
jphayes921's Avatar
 
Join Date: Mar 2017
Location: Linden, MI
Posts: 53
I had similar issue with my tank getting the plumbing to flow just right. It ended up being the 90s on the drains. Changed to flexible pvc and all my issues were gone. Just trapped too much air in the drains.


jphayes921 is offline   Reply With Quote
Unread 05/21/2019, 09:16 AM   #11
Sharpimage
Registered Member
 
Join Date: Jun 2016
Posts: 324
The water should not be at the tip top of the tank. You need to turn down the return pump. Your not getting enough flow from the weir to the drain box. That flow will be limited by the 3/4 inch fittings. Nothing you can do about that.

Then you will need to close the valve more to match the siphon to the overflow box flow


Sharpimage is offline   Reply With Quote
Unread 05/21/2019, 10:29 AM   #12
mr9iron
15& Over Club
 
mr9iron's Avatar
 
Join Date: Feb 2001
Location: Missouri
Posts: 2,552
Blog Entries: 1
Quote:
Originally Posted by Sharpimage View Post
The water should not be at the tip top of the tank. You need to turn down the return pump. Your not getting enough flow from the weir to the drain box. That flow will be limited by the 3/4 inch fittings. Nothing you can do about that.

Then you will need to close the valve more to match the siphon to the overflow box flow


That’s kind of what I was thinking. By moving the gate valve to the sump it would allow the 3/4 pipe to fill the 1” pipe and I could make the proper adjustments then.

I can always adjust the flow from the return pump.

Thank you.


Sent from my iPhone using Tapatalk


__________________
Vince
______________________________

Current Tank Info: Frag tank at the moment, planning another
mr9iron is offline   Reply With Quote
Unread 05/22/2019, 06:47 PM   #13
Sharpimage
Registered Member
 
Join Date: Jun 2016
Posts: 324
I don't think the position of the gate valve is the problem. I think it is too much return from your pump


Sharpimage is offline   Reply With Quote
Unread 05/22/2019, 10:14 PM   #14
mr9iron
15& Over Club
 
mr9iron's Avatar
 
Join Date: Feb 2001
Location: Missouri
Posts: 2,552
Blog Entries: 1
Quote:
Originally Posted by Sharpimage View Post
I don't think the position of the gate valve is the problem. I think it is too much return from your pump


Even if I adjust the pump to the lowest setting? You think that would be too much flow?


Sent from my iPhone using Tapatalk


__________________
Vince
______________________________

Current Tank Info: Frag tank at the moment, planning another
mr9iron is offline   Reply With Quote
Unread 05/23/2019, 12:13 PM   #15
thejuggernaut
Registered Member
 
Join Date: Sep 2006
Location: Lake Jackson, Tx
Posts: 548
I would turn the pump down to about half. Then adjust the gate valve to match. You are overwhelming that 1200 gph overflow. I wouldn't put more than about 600 GPH through it. Then I would adjust the position of my emergency so that it is higher, as well as the open channel. When running normally you want the water as high as you can safely get it in the rear box. Then it will make much less noise.


thejuggernaut is offline   Reply With Quote
Unread 05/26/2019, 05:58 PM   #16
Roy Arena
Registered Member
 
Roy Arena's Avatar
 
Join Date: Aug 2003
Location: Chandler AZ.
Posts: 202
Turn the pump down so you don't overflow the tank. In order to raise the level in the overflow box you will need to close the gate valve on the primary siphon. I didn't see it in the video but I thought on a bean style you want to have a gate valve on your secondary as well. The secondary will also need to be below the water level inside overflow box but at a higher than level than the primary. It doesn't matter where the gate valves are located. I hope this helps.


Roy Arena is offline   Reply With Quote
Unread 05/26/2019, 06:03 PM   #17
Roy Arena
Registered Member
 
Roy Arena's Avatar
 
Join Date: Aug 2003
Location: Chandler AZ.
Posts: 202
http://reefcentral.com/forums/showth...7#post14058977


Roy Arena is offline   Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



All times are GMT -6. The time now is 05:15 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2024 Axivo Inc.
Use of this web site is subject to the terms and conditions described in the user agreement.
Reef CentralTM Reef Central, LLC. Copyright ©1999-2022
User Alert System provided by Advanced User Tagging v3.3.0 (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.