|
01/26/2017, 09:48 PM | #1 |
Registered Member
Join Date: Mar 2015
Location: Canada
Posts: 73
|
School project clownfish breeding diary
introduction:
So as you can see, I am a student who studies in the field of biology and this year I have a course of breeding of living organism. My team and i decided to choose saltwater fish cause i always wanted to do marine breeding to gain experience and learn more about aquaculture as an marine aquarist and that's what I'd like to do for my career. We decided to choose the clownfish (Amphiprion ocellaris), cause its one of the fish that is the easiest to breed (read a lots of books and web) in captivity. I decided to share my project in this forum, because there is a lot of peoples who reads thread on this forum and a lot of them are expert than me. So i can learn from the advice and share their experience with clown breeding. So dont be affraid to comment or write some fact to share. (srry if my english is hard to understand...) So lets get started! Here Set-up info: -40 gal. tank (i dont know if 40 is too big for a pair...) -aquamaxx hang-on skimmer (for chemical/mechanical filtration) -hang-on filter with carbon, marine pure and sponge (for bio/mechanical filtration) -airstone (oxygen) -heater+thermometer -flower pot (hiding spot for fish) p.s one disavantage is that i dont have sump cause $$$. Day 1. The aquarium is installated, cleaned and filled with mixed saltwater at 1.021 sp. gravity. To start the nitrifying cycle and to established the tank faster i used the product Bio S from Aquaforest. Filter and skimmer are in function and the heater is set to 24°C. For now, i plan to wait at least 2 weeks(instruction from bio S) before adding the fish. The pair is already formed (sub-adult)and they are waiting at the LFS during the maturation of the tank. Question for you readers: 1-is there something i miss in the set-up? 2-do i need to add a wavemaker? thank you to be continued... |
01/27/2017, 02:59 PM | #2 |
Registered Member
Join Date: Mar 2014
Location: Maryland
Posts: 1,671
|
A couple small suggestions:
dump the air-stone and add a power head. The power head by itself will turn over your water to keep it oxegynated and keep detritus off the bottom so it can be filtered out. I would replace the sponge every three days to avoid letting the trapped organics rot into nitrate. Alternatively just pull it out, you should get faster flow through the rest of the media that way. Good Luck. |
01/27/2017, 10:15 PM | #3 |
Registered Member
Join Date: Mar 2015
Location: Canada
Posts: 73
|
When you say replace the sponge, do you mean clen it every 3 days or change to new one?
Also, it would be better with no sponge and the filter media will be only carbon and marine pure sphere? |
01/27/2017, 10:26 PM | #4 | |
Registered Member
Join Date: May 2016
Posts: 549
|
Quote:
Yes he is saying just do carbon and the spheres Sent from my iPhone using Tapatalk |
|
01/28/2017, 03:26 PM | #5 |
Registered Member
Join Date: Mar 2015
Location: Canada
Posts: 73
|
Day 2
no news Day 3 test my water param and its going good: Salinity : 1,021 pH: 8.4 ammonia:0 nitrite:0 I put a damself fish for test fish and to cycle the tank faster. one problem i did a water change (5%) and used tap water witout using prime (shame on me) do i have to start over cause i killed the good bacteria or it should be fine for dat quantity.(i know they are metal, phosphate and other bad stuff...) to be continued |
01/28/2017, 08:01 PM | #6 |
Registered Member
Join Date: May 2016
Posts: 549
|
1) why is your salinity not 1.025
2) cycling with a fish is now considered cruel and not a common practice 3) if you're raising clownfish eggs then it is important to have clean water for good quality fish. I don't know how important a 5% water change is but you need to use RODI instead IMO Sent from my iPhone using Tapatalk |
01/28/2017, 11:55 PM | #7 |
Registered Member
Join Date: Mar 2015
Location: Canada
Posts: 73
|
-the salinity is 1,021 cause i read that its reduce the stress of osmoregulation to the fish, so less energy is waste.
-lot of bacteria product (atm colony, dr.tim's, bios...) allow to put a hardy fish from day 2 but with a small bioload. -i wanted to say that i added new water instead of water change. for rodi water ill purchase it from my lfs next time. |
01/29/2017, 07:54 AM | #8 |
Registered Member
Join Date: May 2001
Location: Mississauga,Canada
Posts: 323
|
you can bring salinity lower
1.020 will be easier to raise the larva. what kind of clowns are you going to try and raise |
01/29/2017, 10:09 AM | #9 |
Registered Member
Join Date: Mar 2015
Location: Canada
Posts: 73
|
|
01/29/2017, 06:05 PM | #10 |
Registered Member
Join Date: Dec 2015
Location: Mendham, NJ USA
Posts: 395
|
You are lucky there is so much info to be found here in the forums from past successes on breeding clowns it should be fun. Don't forget you will need another smaller tank to raise the fry. I used a 2.5 gallon for one month then moved them to a 10 gallon. Both with sponge filters. You tube was a great help too. Good luck.
|
02/02/2017, 06:22 PM | #11 |
Registered Member
Join Date: Mar 2015
Location: Canada
Posts: 73
|
little update
day 8, Water param are doing fine and the little damself is doing a great job for cyclying the tank with no stress. water parameters: pH: 8.3 ammonia:0 nitrite:0 kH: 10.5 salinity : 1.021 My thoughts on the product BIO S from aquaforest: -its a great product and the tank can be cycled faster than they say in the instructions (2 weeks). It took me 3-5 days. - Compare to other bacteria product they are highly concentrated, good price and less quantity to use to cycle. to be continued |
02/02/2017, 06:48 PM | #12 |
Registered Member
Join Date: Mar 2008
Location: selden N.Y.
Posts: 885
|
good luck with your project you can look in to reed mariculture ap breed have good products you can get rotifer cultures and feed they are very helpful also
__________________
Life is good Current Tank Info: 75gal reef ready koralia 3, 30g sump, 4b 48" t5s lighting, 29g reef with breeding pair clowns 55g reef 55g freshwater |
02/05/2017, 09:17 AM | #13 |
Registered Member
Join Date: May 2001
Location: Mississauga,Canada
Posts: 323
|
where in Canada are you
|
02/05/2017, 12:32 PM | #14 |
Registered Member
Join Date: Mar 2015
Location: Canada
Posts: 73
|
|
02/06/2017, 08:58 PM | #15 |
Registered Member
Join Date: Mar 2014
Location: L.A./Tahoe
Posts: 6,003
|
Hopefully you're just a freshman or sophomore in college. Those clowns can take 2+ years to start breeding. Good luck with the project.
|
02/13/2017, 09:01 AM | #16 | |
Registered Member
Join Date: Oct 2014
Location: Westchester, NY
Posts: 439
|
Quote:
+1 Unless you are buying a breeding pair, which can be pricey, this can take quite a while. There is a big difference between a bonded pair and a pair that is actively laying eggs. Honestly you would be well served if you could find a hobbiest breeder in your area to befriend. I helped a high school student out with a similar project. Her fish weren't laying, so I gave her some two week old fry to raise. The forty gallon tank is much bigger than breeders typically use for the parents. More common would be ten gallon tank. The 40 is a good size for the grow out tank. You should have a second 10 gallon for the nursery tank. I'd invest in RODI, you will go through a lot of saltwater breeding clownfish. Check out Pickle's clownfish breeding thread. Google, it's on another site. I also have a thread in this section. Good Luck! Howard Sent from my iPhone using Tapatalk
__________________
80 Gallon Innovative Marine long shallow reef 30 Gallon tank for raising baby clownfish Current Tank Info: Innovative Marine SR-80 |
|
02/24/2017, 09:15 PM | #17 |
Registered Member
Join Date: Mar 2015
Location: Canada
Posts: 73
|
little update on whats going on,
its been 2 weeks that our bonded couple pair of clown was introduce and they are doing great. From the first week the female was already eating like a pig then the male and they began to show some reproductive behaviours. At first, the female started to shake her body and head, chasing and bitting the male to show dominance. Then after few days, the male started to tending and cleaning with his mouth and caudal fins the substrate on the flower pots. im planning to raise the temperature from 25 to 27 C and start feeding them more (3 times per day) Also, i would like to know what the best for daylight hour time. Currently, i give them 7 hours of daylight and the rest of hours with no light. to be continued |
02/25/2017, 07:42 AM | #18 |
Registered Member
Join Date: May 2001
Location: Mississauga,Canada
Posts: 323
|
double the light to 14 to 16 hrs
|
02/26/2017, 06:30 AM | #19 |
Registered Member
Join Date: Mar 2014
Location: L.A./Tahoe
Posts: 6,003
|
Joyce Wilkerson recommends 12 hours and that works for my clowns. My tank temperature stays in 80-82 degree range.
|
03/04/2017, 06:41 AM | #20 |
Registered Member
Join Date: Dec 2015
Location: Mendham, NJ USA
Posts: 395
|
I good trigger to bring a fish into breeding condition is feeding more often- 6-8 times a day in smaller than normal amounts. Agree with above, Increase the lighting period over a couple of weeks to 12 hours. Thinking back on when I first tried breeding clowns, from the point of laying their first batch of eggs to the point of having a successful batch to raise was almost a year.... You may want to have a back up plan like breeding fancy Flag Fin Mollies in a saltwater tank vs freshwater. "Just saying"
|
05/30/2017, 01:02 PM | #21 |
Registered Member
Join Date: Nov 2013
Posts: 123
|
Any updates?
Sent from my iPhone using Tapatalk |
05/30/2017, 01:30 PM | #22 |
Registered Member
Join Date: Jan 2016
Location: New Jersey
Posts: 682
|
I would think that college bio class has ended.
__________________
diana |
06/28/2017, 03:09 AM | #23 |
Registered Member
Join Date: Jan 2015
Location: Fremont, CA
Posts: 9,555
|
One of the things that worked well for me to induce spawning with clownfish pairs is adding pairs of dottybacks (P. fridmani is ideal), damsels or Marine Bettas. Especially the dottybacks and Marine Bettas spawn quickly if you make pairs of sexed adults. I had Marine Bettas spawn 2 weeks after pairing them. Dottybacks generally get going after a month or two.
My theory is that the released hormones from the other pairs get the clownfish going. Of course you could also add the hormones directly (should be available from suppliers of fish farm equipment, foods and medications). It's a pretty common method in the commercial fish farming business (the ones breeding food fish).
__________________
Pairs: 4 percula, 3 P. kauderni, 3 D. excisus, 1 ea of P. diacanthus, S. splendidus, C. altivelis O. rosenblatti, D. janssi, S. yasha & a Gramma loreto trio 3 P. diacanthus. 2 C. starcki Current Tank Info: 200 gal 4 tank system (40x28x24 + 40B + 40B sump tank + 20g refugium) + 30x18x18 mixed reef + 20g East Pacific biotop + 20g FW +... |
07/14/2017, 09:09 PM | #24 |
Registered Member
Join Date: Jul 2017
Posts: 2
|
This time the fish farming is too bored, the fish disease throughout, this year harvest losses or poor breeding, the water he always filtered it regularly that fish disease. May my consultant with you. I have not had much experience.
|
Thread Tools | |
|
|