Reef Central Online Community

Go Back   Reef Central Online Community > General Interest Forums > Do It Yourself
Blogs FAQ Calendar Mark Forums Read

Notices

User Tag List

Reply
Thread Tools
Unread 06/18/2018, 07:04 PM   #1
abhishek@1985
Registered Member
 
Join Date: Jul 2010
Location: Minneapolis, MN
Posts: 525
DIY 8020 aluminium light stand - suggestions please

Hi ,

Am planning to use 80/20 to build a strong enough light stand to hold 2 ATI 48 inch bulb fixtures - one 4 bulb and one 6 bulb fixture.

My plan is to simple light stands - 2 of them attached at either end of my wood stand that are 96 inches in height. At the top, attach horizontal bars to each one of them to make a right angle that extend all the way to the front of the tank which will be around 40 inches .

What parts are necessary to build such a light fixture and where can I buy them ? No idea about 80/20 and hence looking for ideas and suggestions.

Regards,
Abhishek


abhishek@1985 is offline   Reply With Quote
Unread 06/18/2018, 09:01 PM   #2
slief
RC Sponsor

 
slief's Avatar
 
Join Date: Sep 2009
Posts: 14,173
Take a look at 8020.net

They have all sorts of T slot extrusion options as well as fasteners. Weight will be a big factor especially with your height as you don’t want the verticals to flex.

At the very least, I would use 50x50mm extrusions for the verticals and horizontals.
https://8020.net/shop/25-5050-black-fb.html


My suggestion would be to draw up what you are looking to build and call 8020 and they will provide a parts list for the extrusions to connect the horizontals with the verticals as well as the nuts and fasteners you will need to attach it to the back of your stand.

You will want to know in advance of calling them, the thread size of the mounting points on the ATI fixture which are likely to be 4mm or 5mm but you need to know that as well so you can figure out how to mount the fixture to the extrusion. If it were me, I’d likely use carriage bolts for that but I’d bet 8020 will have options for that as well.


__________________
Director Customer Support Royal Exclusiv USA
For All Royal Exclusiv & Bubble King questions please refer to our Sponsor forum: http://www.reefcentral.com/forums/fo...play.php?f=745

Current Tank Info: 480G display mixed reef, 90G sump, 90G refugium, 60G display refugium. Check out my build thread: http://www.reefcentral.com/forums/showthread.php?t=1783476
slief is offline   Reply With Quote
Unread 06/18/2018, 09:09 PM   #3
PyroSteve
Registered Member
 
Join Date: Jan 2017
Location: Springfield, PA
Posts: 60
This video might help with what you need for materials.

https://m.youtube.com/watch?ebc=ANyP...&v=9WNSdcHRdqc

You'll need to get brackets to attach it to your stand instead of the glass clamps


PyroSteve is offline   Reply With Quote
Unread 06/20/2018, 11:50 AM   #4
sfsuphysics
Registered Member
 
Join Date: Jan 2004
Location: San Francisco
Posts: 9,103
There's a lot of factors involved in how well it will hold up. One of the big one though is the fasteners used. Take a look at
https://8020.net/university-fastening-options
then scroll down and click on "Fastener application test" to get an idea of what type of fasteners are best suited for your needs, from the sounds of what you want to do (inverted L shape to hold up your lights?) anchor fasteners are going to be your best bet. Also don't take the numbers on that page too literally as the size of the pieces used to get those results for the 1515 (1.5") is only 6" long, although you probably can extrapolate over 40" since it's literally just a torque which you're fighting which changes linearly as the force applied gets farther away from the point of connection i.e. you try to cantilever out 12" instead, then divide the force by 2 (since it's twice as long as the 6" they used). Also those numbers are failure values so want to give yourself some wiggle room.


__________________
Mike
sfsuphysics is offline   Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



All times are GMT -6. The time now is 06:17 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2024 Axivo Inc.
Use of this web site is subject to the terms and conditions described in the user agreement.
Reef CentralTM Reef Central, LLC. Copyright ©1999-2022
User Alert System provided by Advanced User Tagging v3.3.0 (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.