|
12/19/2017, 10:01 AM | #1 |
Registered Member
Join Date: Feb 2012
Posts: 22
|
Test kit results. Api
Testing for akalinity. Test sample water turns blue on 1st drop. Says dkh is 17.8 Also calcium test sample doesn’t turn blue stays purple. How to correct these results. Tank is a 120.Done 2 water changes on consecutive Fridays approximately 30 gal each time.Using instant ocean.Any advice on how to correct these results.
|
12/19/2017, 10:37 AM | #2 |
Registered Member
Join Date: Sep 2016
Location: St. Augustine, FL
Posts: 1,857
|
Check the test results vs Red Sea, Salifert, or Hanna Checker. I know those can be expensive but they are more reliable than API IMO. If you used IO salt exclusively and you're salinity is 1.024-26 there is no way possible you have an Alk of 17+ unless you've used a pH buffer.
__________________
90g Mixed Reef |
12/19/2017, 10:49 AM | #3 |
Registered Member
Join Date: Feb 2012
Posts: 22
|
Rob you are correct. My dkh was always an 8 and I never added any buffer. I always thought the result was incorrect. I would add calcium when needed to maintain a 400. But the dkh would never go down. So I did add a little and decided to test about 2 weeks ago and the dkh was high. A local pet shop went out of business last week and sold a lot of Stoney corals frags very cheap. I bought some and I didn’t have a choice but to put them in my tank. I hope all the water changes I do doesn’t kill them.
|
12/19/2017, 11:01 AM | #4 |
Registered Member
Join Date: Sep 2016
Location: St. Augustine, FL
Posts: 1,857
|
Water changes will never kill anything so long as the salt mix is done to the correct salinity/sg. I suggest starting a log and running the basic battery of tests to get a starting point. For reference there is a salt mix guide which outlines basic parameters (Alk, Cal, & Mag) for the various brands.
As for Alk now, don't supplement any until you have a satisfactory test result(s) you are confident in.
__________________
90g Mixed Reef |
12/19/2017, 12:47 PM | #5 |
Registered Member
Join Date: Apr 2016
Location: Central Nebraska
Posts: 3,190
|
The test sample is supposed to turn blue on the first drop for the dKH kit. It should take 7-11 drops to change to yellow. The number of drops equals the dKH (alk) reading. You can't achieve a 17.8 reading with this kit. It's only whole numbers.
__________________
Pat Current Tank Info: 125 in-wall , 40b sump. 6 bulb T5. ASM G2 skimmer. LPS and leathers |
12/19/2017, 12:57 PM | #6 | |
Registered Member
Join Date: Sep 2003
Location: North Carolina
Posts: 20,050
|
Quote:
well this below.. As always its very useful to read the directions.. And 1 drop is 17.9ppm which is NOT the same as dKH but as stated you count till it turns yellow.. not blue.. 1 drop is 1dKH (or 17.9ppm) 8 drops is 8dKH(or 143.2 ppm)
__________________
Who me? |
|
12/19/2017, 01:08 PM | #7 |
Registered Member
Join Date: Feb 2012
Posts: 22
|
Thanks for clearing up test. I ran test for alklanity, cal, mg,pH phos and nitrate.I must of misread instructions.
|
12/19/2017, 03:37 PM | #8 |
RC Mod
Join Date: Mar 2002
Location: Mountain View, CA, USA
Posts: 88,616
|
Some calcium kits stay purple unless the solution is mixed well and let to sit for a while for the reaction to complete. I titrated my IO kit until it turned purple, then waited 1 minute, and from there one more drop or so would complete the color change to blue. Your kit might need more time, as well.
__________________
Jonathan Bertoni |
|
|