|
05/10/2010, 10:53 PM | #1 |
Registered Member
Join Date: Feb 2008
Location: Texas
Posts: 703
|
Cutting large holes in plywood?
What is the best method/tools for cutting out neat holes for doors in a large piece of plywood?
|
05/10/2010, 11:22 PM | #2 |
Registered Member
Join Date: Sep 2007
Location: Charlotte, NC
Posts: 4,689
|
A drill and a jigsaw may not be the cleanest, but if you don't have a shop its probably the easiest and more affordable way of cutting holes in wood. I'm assuming something like a table jigsaw would be a little cleaner.
__________________
Ryan |
05/10/2010, 11:35 PM | #3 |
Registered Member
Join Date: May 2010
Posts: 5
|
If you are certain you can draw the cut out square, you might try dropping in a circular saw for the longest part of the cut then clean up the corners with a jig saw. Use the finest tooth blade you can find to get the cleanest cut, and go slow.
|
05/11/2010, 03:47 AM | #4 | |
Registered Member
Join Date: Nov 2009
Location: ridgecrest ca
Posts: 123
|
Quote:
GO SLOW, i am sure u have heard measure 3 times cut 1. and square everything up befor cutting to save yourself from having to redo things. |
|
05/11/2010, 05:03 AM | #5 |
Registered Member
Join Date: Feb 2003
Location: Pittsburgh
Posts: 20,772
|
Rough cut the hole with the jigsaw, leaving 1/4" or so. Then use a router and straightedge to clean up what is left.
You can use a straight edge with the jigsaw also, but if you have access to the router, it will work mutch better. |
05/11/2010, 05:13 AM | #6 | |
Registered Member
Join Date: Apr 2010
Location: Cheektowaga, NY
Posts: 397
|
Quote:
A router and straight edge could also be used to make the entire cut. This is especially useful for cutting large, round holes. |
|
05/11/2010, 06:31 AM | #7 |
Registered Member
Join Date: Feb 2010
Location: Southeast Kansas
Posts: 286
|
I agree with IronMan, as a contractor we use a router, While the jigsaw will work the doors will still have to be trimmed to be able to open, a router with a 1/8 bit will do it all at once. Good Luck.
__________________
75 ga. reef 20 gal. sump corals GSP assorted Polyps Zoos PomPom Xenia Waving Hand Xenia Blue Mushroom Toadstool Leather Current Tank Info: 75g. reef 125 lbs. live rock 90lbs. live sand 1 Clown small Regal Tang 20 Nass. Snails Turbos hermit |
05/11/2010, 10:35 AM | #8 |
Registered Member
Join Date: Apr 2010
Posts: 64
|
You can do it with a straightedge, but I prefer to do it with an outside form and a bottom bearing bit (or a router collet).
Just take 4 strips of 1/2 particle board (or whatever you have lying around) and build a full guide. This way you can guarantee square and have almost no chance of making a mistake (as long as you clamp it down tight). Just make sure the frame is square and flat on both sides. A 1/8" bit is fine, just go slowly or you'll risk snapping it off. |
05/11/2010, 01:56 PM | #9 |
Premium Member
Join Date: Mar 2001
Location: Wyoming
Posts: 2,152
|
And Take pictures
__________________
"If there's nothing wrong with me... then there must be something wrong with the universe!" Current Tank Info: 10 gallon nano with ATS |
05/11/2010, 04:04 PM | #10 | |
Registered Member
Join Date: Feb 2003
Location: Pittsburgh
Posts: 20,772
|
You mean Bean
Quote:
|
|
05/11/2010, 07:26 PM | #11 |
Registered Member
Join Date: Mar 2007
Location: Annapolis, MD
Posts: 68
|
Having worked for a boat manufacturer for about 10 years, the method of choice was a hole saw. You can buy generic hole saws up to 5" or 6", good for plywood, starboard, fiberglass that would be my preference.
Bigffish |
05/11/2010, 07:29 PM | #12 | |
Registered Member
Join Date: Jun 2004
Location: Buffalo, New York
Posts: 1,924
|
Quote:
|
|
05/11/2010, 08:20 PM | #13 |
Registered Member
Join Date: Feb 2008
Location: Texas
Posts: 703
|
|
05/11/2010, 09:29 PM | #14 | |
Registered Member
Join Date: Feb 2003
Location: Pittsburgh
Posts: 20,772
|
Quote:
|
|
05/11/2010, 09:36 PM | #15 | |
Registered Member
Join Date: Feb 2003
Location: Pittsburgh
Posts: 20,772
|
Quote:
If you have a plunge router, you can likely cut the whole panel out in one pass using the template & guide bushing (or bearing bit) method as indicated above. That said, if you are not familiar with using a router with templates, then you will spend more time making the template and messing around than it is worth. As I mentioned, I would rough cut the hole out within 1/8" or so of the finished line using a jig-saw. I would then clamp (or use double sided tape) a straightedge to the panel and use it is a guide. The quickgrip clamps are great for this. Use one straight edge as a guide and another as a STOP so that you don't route too far. Do you have a router? Are you borrowing or buying? |
|
05/11/2010, 10:19 PM | #16 |
Registered Member
Join Date: Feb 2008
Location: Texas
Posts: 703
|
Will be borrowing or buying. I've been reading a lot on router forums dot com and the Craftsman 2hp combo is pretty well liked there as an inexpensive option especially for the new router owner (I haven't used one since high school, 20 or so years ago). So I'm thinking of picking one up.
|
05/12/2010, 05:27 AM | #17 |
Registered Member
Join Date: Apr 2010
Location: Cheektowaga, NY
Posts: 397
|
A template isn't really needed unless you are making the same cut several times. Just use a straight edge as a guide and clamp it in place on all four sides of the cut. The guide should be clamped at a distance equal to the distance from the base of the router to the edge of the router bit. Then just plunge the bit through the panel and follow your guides. Take it slow and let the bit do the work. You'll be surprised at how easily the router bit cuts through the plywood. IMO this is far more efficient that rough cutting the hole then finishing the edges in a separate step but that will certainly get the job done as well.
Make sure to shoot us some pictures when you're done. |
05/12/2010, 07:58 AM | #18 |
Registered Member
Join Date: Feb 2003
Location: Pittsburgh
Posts: 20,772
|
I suggested the rough cut first for a few reasons:
1) so that he does not have to deal with supporting the waste piece. This will prevent cracking and/or binding when the piece sags as material is removed. 2) less depth of cut means less (or no) grabbing 3) less depth of cut meanns less need to regulate feed rate which lessens (removes) the possibility of burning up the bit If he DOES decide to plunge cut the piece, then it should be done resting on a sacraficial surface and he should use a 1/4" UP SPIRAL bit, not a straight sided cutter. |
05/12/2010, 08:21 AM | #19 |
Registered Member
Join Date: Mar 2007
Location: Annapolis, MD
Posts: 68
|
I insert thy foot into thy mouth
Bigffish |
05/12/2010, 09:15 AM | #20 |
Registered Member
Join Date: Aug 2009
Location: Prince Edward Island, Canada
Posts: 196
|
If you don't have a great workshop/space, then I second the rough cut and trim method.
If you are buying a router, then I suggest getting one with an adjustable speed feature, and USE IT. Matching your rotation speed to your bit size can make a nice difference in cutting, and prolonging the life of your bit edge. You are going to try and insert my foot into my mouth, and expect to get away with it? (Old an middle English are dangerous things. Use wisely and with caution.) |
05/12/2010, 09:17 AM | #21 |
Registered Member
Join Date: Feb 2003
Location: Pittsburgh
Posts: 20,772
|
|
05/12/2010, 12:03 PM | #22 |
Registered Member
Join Date: Feb 2008
Location: Texas
Posts: 703
|
Ok, here is another thought. Since this hole on the front of the stand will be the same as the 2x frame perhaps it would be best to do a rough cut with a jig saw and then use a bottom bearing flush trim bit to finish the cut out?
|
05/12/2010, 12:33 PM | #23 |
Registered Member
Join Date: Feb 2003
Location: Pittsburgh
Posts: 20,772
|
As long as your 2x frame is square and smooth
|
05/12/2010, 12:37 PM | #24 |
Registered Member
Join Date: Feb 2008
Location: Texas
Posts: 703
|
That's true, 2x's aren't as smooth as I'd like it so I'll use the straight edge approach.
|
05/12/2010, 09:24 PM | #25 | |
Registered Member
Join Date: Apr 2010
Location: Cheektowaga, NY
Posts: 397
|
Quote:
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
cutting large diameter hole in acrylic | pro2k | Do It Yourself | 3 | 12/16/2009 01:25 PM |
No need to cut a hole in your wall anymore!!! | Atticus | Greater Iowa Reef Society | 8 | 10/24/2006 08:14 PM |
Drilling and waterproofing holes in plywood tanks | Chihuahua6 | Do It Yourself | 4 | 08/19/2006 08:21 AM |
how to cut a hole in acrylic | B33FST3W | Do It Yourself | 8 | 08/17/2006 11:38 AM |
Cutting a hole for a fan | dtaranath | Do It Yourself | 11 | 01/26/2006 01:31 PM |