Tank Monitor and Control V1.0 on Github

MD500_Pilot · 06/06/2020, 09:27 PM

Hello everyone, I have been working hard on my water automation project that I shared with everyone a little bit ago HERE. I am about 70% done with all of the programming and pretty much all done with the hardware (other than putting it in a box):

As part of the overall process of automating my tank as much as possible, I have finally put V1.0.0 of my Fish Tank Monitor and Control up on Github HERE. This will be where the tank water management part will live as part of the overall tank control.

The system is designed to monitor(m), record(r) and provide system notifications(n) on the following parameters:

Temperature (m, r, n)
pH (m, r, n)
Toxic Free Ammonia (NH3) (m, r, n)
Bound Ammonix (NH4) (m, r)
O2 Potential (m, r)
Electrical Conductivity in μS/cm (m, r, n)
Total Disolved Solids in ppm (m, r, n)
PAR (m, r)
LUX (m, r)
Kelvin (m, r)

The system is also designed to allow manual entry of the following parameters:

GH (r)
KH (r)
PO4 (r)

The system allows full power control of the following devices:

Fluval FX6 Filter
Fluval 406 Filter
CO2 Injection System
Air Pump
UV Light

Notifications can be done via E-Mail, SMS, or Pushbullet and are fully customizable.

Main Screen

Notification Management

System Logging

Eventually, when I complete my water automation, the tank control part of it will live here as well.

Hopefully some on you may enjoy looking it over! Thanks

MarAquatic · 06/06/2020, 11:52 PM

When can I get 1

Sent from my SM-N960U using Tapatalk

MD500_Pilot · 06/07/2020, 11:49 AM

Quote:

Originally Posted by MarAquatic

When can I get 1

Sent from my SM-N960U using Tapatalk

:-) All the code is up on GitHub now!!

v8maro · 07/03/2020, 06:51 PM

This is pretty sweet. Once I get a tank running I'll have to get this up and running and use it!! What are you running it on? A raspberry would be pretty cool. Btw, I program (a lot/way too much) so if I get it running I can contribute.

06/06/2020, 09:27 PM	#1
MD500_Pilot Registered Member Join Date: Apr 2020 Posts: 21	Tank Monitor and Control V1.0 on Github Hello everyone, I have been working hard on my water automation project that I shared with everyone a little bit ago HERE. I am about 70% done with all of the programming and pretty much all done with the hardware (other than putting it in a box): As part of the overall process of automating my tank as much as possible, I have finally put V1.0.0 of my Fish Tank Monitor and Control up on Github HERE. This will be where the tank water management part will live as part of the overall tank control. The system is designed to monitor(m), record(r) and provide system notifications(n) on the following parameters: Temperature (m, r, n) pH (m, r, n) Toxic Free Ammonia (NH3) (m, r, n) Bound Ammonix (NH4) (m, r) O2 Potential (m, r) Electrical Conductivity in μS/cm (m, r, n) Total Disolved Solids in ppm (m, r, n) PAR (m, r) LUX (m, r) Kelvin (m, r) The system is also designed to allow manual entry of the following parameters: GH (r) KH (r) PO4 (r) The system allows full power control of the following devices: Fluval FX6 Filter Fluval 406 Filter CO2 Injection System Air Pump UV Light Notifications can be done via E-Mail, SMS, or Pushbullet and are fully customizable. Main Screen Notification Management System Logging Eventually, when I complete my water automation, the tank control part of it will live here as well. Hopefully some on you may enjoy looking it over! Thanks

06/06/2020, 11:52 PM	#2
MarAquatic Registered Member Join Date: Mar 2016 Posts: 689	When can I get 1 Sent from my SM-N960U using Tapatalk

07/03/2020, 06:51 PM	#4
v8maro Registered Member Join Date: Aug 2005 Location: West Bloomfield, MI Posts: 386	This is pretty sweet. Once I get a tank running I'll have to get this up and running and use it!! What are you running it on? A raspberry would be pretty cool. Btw, I program (a lot/way too much) so if I get it running I can contribute.