|
10/03/2017, 02:37 PM | #76 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
Maybe using some dye to tranduce the signal to the visible spectrum is the way to go. Green laser pointers are cheap, IR optics are much too expensive
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps |
10/03/2017, 11:53 PM | #77 | |
Registered Member
Join Date: Jun 2005
Location: Lincoln, NE
Posts: 318
|
Quote:
You don't inherently need to collimate the beam. It helps greatly with optical through put and eliminates/minimizes sensitivities to surface characteristics of the optical bench though. For standards, sure you could mix gas as a transfer standard from a working meter. But that means you have a meter already that has a greater accuracy than what you desire in your DIY version. You can also use precision syringes and a precision mixing volume to generate standards. This might actually be doable pretty cheaply as I think about. As to absorption as a function of gas density. It may appear linear over a narrow range, but it is inherently not. Probably best to think about it on a narrow wavelength basis and build up from there. This is important for thinking about where a gas absorbs as well. Because while you are correct on major regions of absorption, CO2 has individual lines and small groups of lines peppered through out the IR region. Some more useful than others depending on your IR source, filters and detection limit. In any case, absorption on a per wavelength bases (Av) can be expressed as: Av = 1-e^(-kv*l*d) Where l is the optical path length and d is absorber density. kv is the absorption coefficient at v, which is a function of line strength and halfwidth. Line strength saturates at some point. I have lofty dreams of trying out some of the cheap NDIR sensors but haven't gotten to yet; too many more important projects to get through first. But when I do I will report what I find. I had seen most had limited resolution and had hoped that there may be some way of working around that. Hopefully we shall see at some point. I wasn't aware of the drift correction. The direction of the correction seems curious to me though. Do you know if they are using a reference gas cell? Diffusion into the reference cell over time would make sense for the need to correct upward. Or maybe its a source aging issue.
__________________
Current build thread : http://www.reefcentral.com/forums/showthread.php?t=2547305 I ate a jellyfish... tasted like soy sauce. Current Tank Info: 180 gallon system in progress |
|
10/03/2017, 11:57 PM | #78 | |
Registered Member
Join Date: Jun 2005
Location: Lincoln, NE
Posts: 318
|
Quote:
There should be some visible dye suitable for this. I know we typically use a titration method (and that seems the approach used in the automated monitors coming out). But I am pretty Hatch or somebody along those lines make a single reagent that segregates into two forms with different peak absorption wavelengths in the visible spectrum based on alkalinity.
__________________
Current build thread : http://www.reefcentral.com/forums/showthread.php?t=2547305 I ate a jellyfish... tasted like soy sauce. Current Tank Info: 180 gallon system in progress |
|
10/04/2017, 12:00 PM | #79 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
sound like we want a colorimetric drop checker
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps |
10/04/2017, 12:31 PM | #80 |
Registered Member
Join Date: May 2004
Location: Dallas, TX
Posts: 11,033
|
Another incomplete project from years ago
http://www.reefcentral.com/forums/sh...tic+alk&page=9 Need to clone myself or make enough $ to retire so I can tinker more
__________________
Failure isn't an option It's a requirement. 660g 380inwall+280smp/surge S/L/Soft/Maxima/RBTA/Clown/Chromis/Anthias/Tang/Mandarin/Jawfish/Goby/Wrasse/D'back. DIY 12' Skimmer ActuatedSurge ConcreteScape |
10/04/2017, 01:32 PM | #81 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
I've been trying to find a way around titration. Use a chuvette as the drop checker (headspace) with an led, proper dye and a photo sensor. A reference would be nice too. Raising the response rate would require an interesting setup.
Beautiful project by the way
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps |
10/04/2017, 02:38 PM | #82 | |
Registered Member
Join Date: Aug 2012
Location: Brampton, ON, Canada
Posts: 958
|
Quote:
I am leaning towards doing a regular titration with a colorimeter to detect the end point. To get around the issues with volume accuracy, I plan to use a load cell to calculate the various weights of the sample and reagent rather than try to keep pumps from drifting. Dennis
__________________
560G Miracles tank in process making a DIY DyMiCo style filter (for 560G) Current Tank Info: 560G Miracles tank in progress, 80Frag Temporary |
|
10/05/2017, 08:03 AM | #83 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
Much smarter with weighing the sample, but you will still need to calibrate that pretty often?
The problem I see with titration is too many moving parts, each of which has some variability.
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps |
10/05/2017, 07:18 PM | #84 |
Registered Member
Join Date: May 2004
Location: Dallas, TX
Posts: 11,033
|
So... different direction:
Was talking to a reef buddy of mine about this and had an idea about measuring CO2 in the air by pH... So visualize a 5 gallon jug with RODI low dKH water and an air stone (pump has intake filter). The water has a pH probe in it and there's a loop of hose that allows water to recondense back into the jug as the air leaves. Kinda like a drop checker with a pH probe. Now, the pH should be proportional to CO2...
__________________
Failure isn't an option It's a requirement. 660g 380inwall+280smp/surge S/L/Soft/Maxima/RBTA/Clown/Chromis/Anthias/Tang/Mandarin/Jawfish/Goby/Wrasse/D'back. DIY 12' Skimmer ActuatedSurge ConcreteScape |
10/06/2017, 03:08 AM | #85 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
Exactly what I’m thinking, cycle the headspace with an inline air pump.instead of a pH meter, use a ph sensitive dye, laser pointer (already collimated and tight band) and a photosensor.
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps |
10/06/2017, 06:35 AM | #86 |
Registered Member
Join Date: May 2004
Location: Dallas, TX
Posts: 11,033
|
Why? pH meters are already integrated into an Apex and can easily be calibrated, sourced, etc...
__________________
Failure isn't an option It's a requirement. 660g 380inwall+280smp/surge S/L/Soft/Maxima/RBTA/Clown/Chromis/Anthias/Tang/Mandarin/Jawfish/Goby/Wrasse/D'back. DIY 12' Skimmer ActuatedSurge ConcreteScape |
10/06/2017, 06:46 AM | #87 |
Registered Member
Join Date: May 2004
Location: Dallas, TX
Posts: 11,033
|
Also, the reference jug could be any liquid where the pH and air CO2 can be correlated. I'm thinking of a thickened water formula to minimize any evaporation? As long as the inlet air for this test volume and the reef tank are the same, the formulas would apply directly to provide Alk. Almost all the needed parameters can be measured with conventional devices- pH, temp, salinity, pH(CO2). Barometric pressure is the only one to be assumed relatively constant.
The last gap is a fit that converts the test volume pH to air CO2 and an interface processor that collects all the data live and calculates Alk, then feeds it back as an analog or digital reading back to the Apex.
__________________
Failure isn't an option It's a requirement. 660g 380inwall+280smp/surge S/L/Soft/Maxima/RBTA/Clown/Chromis/Anthias/Tang/Mandarin/Jawfish/Goby/Wrasse/D'back. DIY 12' Skimmer ActuatedSurge ConcreteScape |
10/06/2017, 07:01 AM | #88 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
Wish I had me an Apex, that is probably why I don't focus on integrating to one. I think the liquid needs to be water, what else would you use? Many other liquids are volatile and would end up in the tank water eventually. Agar has large pores but I don't think you want to slow the diffusion down through reference solution, I think quite the opposite we want air vigorously pumping through, like your air injectors, keeping the headspace equilibrium. pH meters are expensive for nice ones, like $100 for a good probe with longevity. Green laser diode $5, dye free essentially, photosensor $2-5, half mirror $10, I'm sure there will be hidden costs. Think hanna phosphate checker. Total cost of around $30 tops and likely better resolution than could be had with a pH probe.
If the reference solution is isotonic with the other liquid (tank water) in contact through the headspace there shouldn't be evaporation. The headspace will be saturated with humidity. I'm sure a pH meter would work just fine
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps Last edited by orcafood; 10/06/2017 at 07:14 AM. |
10/06/2017, 10:03 AM | #89 |
Registered Member
Join Date: May 2004
Location: Dallas, TX
Posts: 11,033
|
I think there's a confusion about the CO2 liquid pH sensor.
This is a completely separate and independent device that is sampling air not connected to the tank at all. It can be anywhere and can run oil if need be (not saying that's a good choice - just emphasizing that the liquid and pH sensor have nothing to do with the tank.) The idea is that I'm not relying on headspace. I'm actively injecting air into the tank water and this sampling device simultaneously. I'm sampling the air going in and relying on my injectors to keep the gas in system at the measured rate.
__________________
Failure isn't an option It's a requirement. 660g 380inwall+280smp/surge S/L/Soft/Maxima/RBTA/Clown/Chromis/Anthias/Tang/Mandarin/Jawfish/Goby/Wrasse/D'back. DIY 12' Skimmer ActuatedSurge ConcreteScape |
10/06/2017, 10:55 AM | #90 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
Makes sense to me, outside is your headspace. I still recommend the design should bubble air through the solution being tested for pH rather than rely on diffusion.
Should work with a serious air injection system on a tank, such as yours. Otherwise the headspace might need to be used. Ideally we need to know the pH of the solution to at least the thousands place, which you are not going to get with a meter, not to mention the pH meter will drift.
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps |
10/06/2017, 02:29 PM | #91 |
Registered Member
Join Date: May 2004
Location: Dallas, TX
Posts: 11,033
|
I calibrate pH meters often
Yes. I was pushing the same air through the airstone. Maybe a surface treatment for the water would reduce evaporation.
__________________
Failure isn't an option It's a requirement. 660g 380inwall+280smp/surge S/L/Soft/Maxima/RBTA/Clown/Chromis/Anthias/Tang/Mandarin/Jawfish/Goby/Wrasse/D'back. DIY 12' Skimmer ActuatedSurge ConcreteScape |
10/06/2017, 02:32 PM | #92 |
Registered Member
Join Date: May 2004
Location: Dallas, TX
Posts: 11,033
|
Accuracy does matter but maybe there's a way to make the water very low in alkalinity so that it responds more aggressively to CO2
__________________
Failure isn't an option It's a requirement. 660g 380inwall+280smp/surge S/L/Soft/Maxima/RBTA/Clown/Chromis/Anthias/Tang/Mandarin/Jawfish/Goby/Wrasse/D'back. DIY 12' Skimmer ActuatedSurge ConcreteScape |
10/06/2017, 02:41 PM | #93 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
A dkh around 0.1 might do. Once I get some time I will start to play with making a low range co2 drop checker, I have bromothymol blue sitting right here ready to go.
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps Last edited by orcafood; 10/06/2017 at 02:49 PM. |
10/07/2017, 05:26 AM | #94 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
Hey Karim how accurate is your pH meter? To the tenths or hundredths? Alternatively can you link me to the probe your using?
Do you know the standard error of your kH estimate? Or perhaps do you have a distribution of your estimates over some time period so we could figure out the standard error?
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps |
10/07/2017, 09:12 AM | #95 |
Registered Member
Join Date: May 2004
Location: Dallas, TX
Posts: 11,033
|
The scientific probe by Apex is what I use. Reading is in the hundreds 8.33
But I assume an error of +- 0.05 which is wild, I know. I calibrate monthly though and I use two probes (one regular) in case on drifts. They're never the same value, usually off by 0.1. One I use for the feedback and one I use to stop anything running off the rails.
__________________
Failure isn't an option It's a requirement. 660g 380inwall+280smp/surge S/L/Soft/Maxima/RBTA/Clown/Chromis/Anthias/Tang/Mandarin/Jawfish/Goby/Wrasse/D'back. DIY 12' Skimmer ActuatedSurge ConcreteScape |
10/07/2017, 09:18 AM | #96 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
What kind of variation on your kH estimate do you get? Does it vary by a few points between estimates or a full degree?
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps |
10/07/2017, 12:56 PM | #97 |
Registered Member
Join Date: May 2004
Location: Dallas, TX
Posts: 11,033
|
My purpose isn't to lock in to a particular kH value. This method is intended to get close, but then maintain it over time. I'm really reducing variability.
Since the errors in my system are relatively constant, maintaining my pH aligns with maintaining my dKH stability... so it's all about precision, not accuracy
__________________
Failure isn't an option It's a requirement. 660g 380inwall+280smp/surge S/L/Soft/Maxima/RBTA/Clown/Chromis/Anthias/Tang/Mandarin/Jawfish/Goby/Wrasse/D'back. DIY 12' Skimmer ActuatedSurge ConcreteScape |
10/07/2017, 01:20 PM | #98 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
So what kind of values do you get?
A value means nothing without error. Scientific papers require error for good reason.
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps |
10/07/2017, 02:11 PM | #99 |
Registered Member
Join Date: May 2004
Location: Dallas, TX
Posts: 11,033
|
Sure. But if my error is constant and I can calibrate it out, it doesn't impact me much. The thread I posted showed the measured vs. calculated Alk chart. Got to dig it back up.
Overall, I can keep my dKH between 7.5 and 8.5 by keeping pH between 8.34 and 8.35
__________________
Failure isn't an option It's a requirement. 660g 380inwall+280smp/surge S/L/Soft/Maxima/RBTA/Clown/Chromis/Anthias/Tang/Mandarin/Jawfish/Goby/Wrasse/D'back. DIY 12' Skimmer ActuatedSurge ConcreteScape |
10/09/2017, 01:24 PM | #100 |
Registered Member
Join Date: Nov 2007
Location: Raleigh
Posts: 864
|
Is your alkalinity approximation steady over time? Or does it jump around each subsequent calculation? Over the span of an hour what would be the max and min alkalinity approximation you get?
__________________
Acros, Zoas, Lps and Acros Kevin Current Tank Info: 200 gallon sps |
|
|