|
07/06/2017, 08:13 PM | #1 |
Registered Member
Join Date: Aug 2004
Location: Fallbrook, CA
Posts: 3,049
|
6105 noise help
Hello!
Back on 4/20/2017 I installed a new Tunze 6105 in my tank to replace a smaller nano Tunze controllable pump for more flow. It vibrated some but I didn't worry about that because I know they often do until they break in. Now, more than 2 months later it is still making an audiable hum that I can clearly hear over the TV from 15 feet away and this is running at only 45% (controlled by an Apex). It's fairly quiet at 30% (lowest setting it's supposed to run at) but it can be clearly heard through walls, over the TV, and the air conditioner on 100%. My other Tunze 6105 that I've had for about 2 years is dead silent at 95% with the 18V chip and has been since the first month of operation. My old 6100's were too. What can I do? I've tried everything to clean it with no effect but it seems like the impeller might be out of balance. Thank you, Whiskey
__________________
This video shows 15 months of coral growth in my tank in a 30 second timelapse: https://youtu.be/bF6C57aTDEo |
07/07/2017, 08:36 AM | #2 |
RC Sponsor
Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
The propeller assembly is likely out of balance, it is the only moving part, outside of some direct hard surface contact (feet missing from magnet, side of pump up against the tank wall, cable reverberating against a reflector) this is really the only possible cause, if you PM me your address and purchase info I will send a propeller.
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
07/07/2017, 09:39 AM | #3 |
Registered Member
Join Date: Aug 2004
Location: Fallbrook, CA
Posts: 3,049
|
You are awesome Rodger! A PM is on it's way!
I did double check all the rubber feet, the pump is more than an inch away from any rock or glass, and I have the cord suspended by rubber band in the hood because if it hits the tank or hood the vibration noise is worse. With my other pump of course it doesn't matter where the cord lays, it's still silent. Thank you! Whiskey
__________________
This video shows 15 months of coral growth in my tank in a 30 second timelapse: https://youtu.be/bF6C57aTDEo |
02/14/2018, 12:58 AM | #4 |
Registered Member
|
I have older, probably 2-3 year old 6105’s. Just cleaned them vingar bath a week ago and they are making noise. One more than the other. Are there bushings I can replace too or is it just the props? It’s not that it’s loud, it’s just not the dead silent that I have grown accustomed to with tunze.
__________________
Originally posted by yellowslayer13: "I hate that hole" Current Tank Info: SCMAS Member 225 peninsula euroreef RS180 Apex 400W X 3 20k radiums / Spectra mixed SPS |
02/14/2018, 09:30 AM | #5 |
RC Sponsor
Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
It might be just air in the pumps, if so 2-3 days and it should be gone. Bushing 3005.740 can be replaced, this can be compressed or worn and you will need a pick tool/ o-ring removal tool to hook it from the bottom of the shaft and pull it out. In some cases if the pump was really dirty with fine sand and calcium deposits it can grind the inner hole in the impeller magnet into an ellipse and that will the wobble when clean and make noise.
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
|
|