|
03/29/2018, 10:01 AM | #26 | |
R.C. Fraternity President
|
Quote:
Good to hear from you. I haven't given much thought to when the tank will start to fill with water. I think because it's so far down the road that I don't want to even think about it... There's so many unknown variables, but if you twist my arm, I would say another 2 months. Somewhere around July, right when we have to close up all the doors and windows and start pumping air conditioning. Maybe next time you're up this way in Tonopah you can come see it for yourself...
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
|
03/29/2018, 12:47 PM | #27 |
Registered Member
Join Date: Mar 2011
Location: Golden, CO
Posts: 340
|
Hiding the Apex cables in the wall takes this to a new level of build. I’m glad you’re planning ahead a little with extra cables you don’t have a need for immediately.
Have you considered running a conduit of some sort to the various corners of the room? Something you could fish data cables through in the future as needed? I ended up just using cable raceway outside of the walls because the design changed 10 times before I was done. This is a far cleaner install. |
03/29/2018, 07:27 PM | #28 | |
R.C. Fraternity President
|
Quote:
I did think about it and ruled out that idea because as much as it seems like I have hard fast plans on where everything is going to go, I don't. Usually I wouldn't be able to tell you what is going where a week from now, but when it's 7 days later I can tell you my exact plan, and that's bound to change many times in the course of the day. So running conduit at specific end points would have limited me to those points. Looking back on what I did and how much wire I snaked through the wall, I would definitely lean towards the using conduit. Although, if I really wanted to, I can find those data cables anywhere in the wall and tap into them from that location, if it was conduit I couldn't do that. 6 of one, half dozen of the other....
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
|
03/30/2018, 05:40 PM | #29 |
R.C. Fraternity President
|
Not much to report, although I think you'll get a laugh at my expense. (read on)
I wanted to get the exhaust fan installed Taped all the holes and seems Stabbed it in the ceiling Duct work put 2 holes ei destroyed the house Stucco patch Painted all that's left is to put the drywall pieces back in place We chose this particular fan because it uses a DC motor which equated to lower electric costs and it's rated at 0.6 sones meaning that it's quieter than a high end refrigerator. In fact if you're ever in the market for a new exhaust fan I would urge you to consider this one. Here's a video Apparently the bearings that hold the motor shaft isn't align properly. So, I put in a phone call to the manufacturer and explained to them that the fan didn't meet my standards of quiet, I proceeded to explain to him the problem and he wanted me to email him a video (luckily I already made one for RC) but I couldn't send it to him while on the phone, so he wanted me to hold the phone to the fan and ~maybe he'll be able to hear it. He also added that with these newer phones, he may not be able to hear it. because the phones microphone can pick up all sorts of ambient surrounding noises. I played along, "Ok, I'll close the door and be extremely quiet" Well, long story short they're sending out a replacement, I just have to wait a little longer to check this part off the list. Hope you got a laugh at that...
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
04/02/2018, 09:15 PM | #30 |
R.C. Fraternity President
|
Next step in the process is that I'm running water lines in the wall, three 1/4" lines will go to the tank (ATO reservoir, auto water change in, and out), the other side of the lines will be over on the wall with the RODI.
I thought about this for a while, I wanted to use 1/4" quick disconnect couplers and attach them to a wall plate only having a small portion of the coupler protruding through the wall, the rest would be behind the wall. I ran this idea through a buddy of mine in california, he's a reefer as well but on another level than I. If he said "yay" I would proceed. However his concerns were pretty much mine as well, having a plastic water line connection behind the wall was recipe for disaster. I've never seen one of these fail or leak, but put it behind a wall and it will, and i'll never know until it's too late. So I had to put the quick disconnect coupling on the outside of the wall plate. Not what I wanted but form has to follow function. I have a laser cutter that can pretty much cut any shape from up to 1/2" acrylic, I planned out my cuts on the CAD program and sent it to the laser. The entire purpose of what I'm making is to be able to clamp the tubes and hold them secure to the wall plate, preventing the tubes from sliding out or further back into the wall. All the pieces cut, Adhere these pieces together with weldon 4 Ran a tap through the appropriate holes Starting to come together Front side Ran the tubes through and tighten the clamp to prevent it from backing out Drilled the holes in the wally plate to match the clamping system Trimmed the hose
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
04/02/2018, 09:16 PM | #31 |
R.C. Fraternity President
|
and attached the couplers
Now it's ready for to be connected to the tank. I have to do this to 3 other locations and one that fan comes in, I can start drywalling.
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
04/03/2018, 06:45 AM | #32 |
Registered Member
Join Date: Dec 2012
Location: Michigan
Posts: 1,735
|
Maybe consider putting the water lines below the electric outlets??
I actually have had one of them fail on me. It was a 3/8" push fitting and the end of it just blew out of the housing completely. Luckily I was home and could hear the water spraying all over my utility room when I came downstairs. Everyone I told was surprised at the failure but it definitely DOES happen so good on you for not putting those IN the wall. |
04/03/2018, 09:04 AM | #33 | |
R.C. Fraternity President
|
Quote:
My concern isn't having that power outlet under those lines. Its hard ingredients the tank right above it... hehe
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
|
04/04/2018, 04:07 PM | #34 |
R.C. Fraternity President
|
I've been doing a lot of tedious work, tidy'd up all the wires, temporarily plugged in all the apex equipment and made sure all the connections worked, spray foamed all the holes to outside, Insulated around all the plumbing in hopes to muffle the sound of water flow, it dampened it a little bit but it's still a bit loud.
I wanted to cover up the beam that ran on the floor with concrete. Non of this is ideal, I wish I didn't have to put a step there but it's the best idea I had for covering it up. I will be tiling the floor and the tank will sit over the step anyway. I will have to create a custom stand to work around this.... oh well, what's more work??? When it comes to concrete, I'm a novice at best. A started a punch list of things that I need to do before I can start hanging drywall, out of the 11 things on the list I have 8 done... 3 more to go and I can drywall, then tile, then turn my attention to all things a normal tank build would have. Hopefully all this ground work will pay off during that part.
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
04/05/2018, 08:04 AM | #36 |
Registered Member
Join Date: Dec 2012
Location: Michigan
Posts: 1,735
|
What kind of exhaust fan did you buy? I assume it is triggered by a humidity set point?
|
04/05/2018, 08:18 AM | #37 |
R.C. Fraternity President
|
Itis a delta breeze SLM80, and yes triggered by your normal run of the mill humidity switch.
I was looking at some more sophisticated ones with better controls but I came back down off that cloud and decided once it's set, I don't have to mess with it. I would however like to have a display in the room that will tell me temperature and humidity.
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
04/05/2018, 10:15 AM | #38 | |
R.C. Fraternity President
|
Quote:
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
|
04/05/2018, 01:34 PM | #39 | |
Registered Member
Join Date: Dec 2012
Location: Michigan
Posts: 1,735
|
Quote:
I asked because I'm thinking of adding a fan to my utility room. I've used a mobile de-humidifier thus far but it's cumbersome, loud, and probably takes a ton of energy. I've already got a vent I could use for a fan, so I might as well add one. I'll check out the one you've listed. Thanks! |
|
04/05/2018, 04:35 PM | #40 |
R.C. Fraternity President
|
From my limited research, I read that 20-40% is ideal for the whole house. That's a safe level to prevent mold growth and not too dry for people comfort. So I set it to 30%, just because it's in between.
The reason why I asked the question is because I have to figure out where to put my portable ac unit if the fan was going to be on constantly I dont want to place the ac under it. But if it's only going to be on periodically then its feasible to do so. The ideal place to put it is in the corner right under the fan, although it has a long enough exhaust hose that I can stretch it further away. As for that exhaust fan, I'm satisfied with it, it's not completely silent, but I quite certain that once everything in the room is running you won't hear it. The good thing about it is that it uses a brushless CD motor which equates to low electrical cost.
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
04/05/2018, 09:32 PM | #41 |
R.C. Fraternity President
|
Today was a slow day, I ran some errands in the morning then I went and met a local reefer Sawcjack00, he's in the beginning stages of a new tank as well and it was a treat to see the start of something awesome! Here's his tank build thread, he has a lot of top of the line equipment... I'm extremely jealous!!
So what did I do after that??? When I bought the sound deadening insulation for around the plumbing, I had enough to do the wall around the tank... It was exactly enough!! The goal is not to hear anything from the living room side of the tank, hopefully it does. and I also brought in the drywall... Again I went with 5/8" drywall to help with sound deadening. I'm still waiting on a few things before I can completely close up the walls, but I can do about 90% of it tomorrow.... Getting closer!!!
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
04/05/2018, 09:46 PM | #42 |
R.C. Fraternity President
|
I don't know how many people are actually reading this, but I have a dilemma. This tank will not be accessible from outside the tank, meaning I can't poke around above or below the tank, all maintenance, feeding, cleaning will be done from behind the tank. This means that I can't paint the back of the tank like I normally would.
I don't want to be able to see through the tank into the equipment room... How do I create the illusion that there's a back to the tank but easily removed to conduct maintenance. Any suggestions to help solve this predicament would be greatly appreciated.
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
04/06/2018, 04:53 AM | #43 |
Registered Member
Join Date: Jan 2011
Location: P.E.I. canada
Posts: 15
|
i found a sheet of lite pvc like material at a sign shop .it was 1/8 to 3/16 thick very light weight i bent a few strips with a heat gun and glued them to the sheet and hung it on back of the tank . the material was flat black .your build is looking great .
|
04/06/2018, 06:42 AM | #44 |
Registered Member
Join Date: Dec 2012
Location: Michigan
Posts: 1,735
|
You don't want to have any access in the front of the tank? I think you may be too worried about sound deadening... if you have a full siphon overflow then the noise is so minimal, especially since your sump is in the basement. That's where all the noise will be. My tank is not in a wall but with the full siphon overflow I can hardly hear anything when I'm right next to the tank. The utility room is just on the other side of the wall (pipes run through wall) and if I have the door closed it's super quiet. My point is that even if you put an access panel (which I do suggest), it'll still be super quiet even with a cooling fan and overflow.
|
04/06/2018, 10:30 AM | #45 |
Registered Member
Join Date: Aug 2009
Location: Minooka Il
Posts: 912
|
Check out copps 1300 gallon build in the sps section. He uses kydex for maintenance and its black. He just cycles through them every so often.
Btw depending on the size of the room and where its located the humistat will most likely run all the time at 30%. I'd play with it but my guess is you'd be better closer to 40%ish. |
04/06/2018, 10:32 AM | #46 |
Registered Member
Join Date: Aug 2009
Location: Minooka Il
Posts: 912
|
The kydex is on page 4
|
04/06/2018, 01:23 PM | #47 |
Registered Member
Join Date: Aug 2011
Location: NJ
Posts: 340
|
I've heard of people using window tinting. You can't see through from the front, but with lights on the tank you can see in from the fish room.
|
04/07/2018, 10:28 AM | #48 | ||||
R.C. Fraternity President
|
Quote:
For aesthetics, my wife and I had many conversations about how the front of the tank should look and one of the things that we came to an agreement on was that there wouldn't be any doors on the front side of the tank. Yes definitely a challenge when maintenance is considered, at the time I though that doing it all from behind wasn't going to be an issue. The ship has sailed when it comes to accessing the tank from the front, now I have engineer my way out of this problem. Quote:
Quote:
Based on your comment and from what I read, I can easily start at 40% and dial it in as I go along. Quote:
McPuff, I see that you inquired about this in earlier thread, did you ever do it?
__________________
Jimmy MASVC President Dishes are done man! Current Tank Info: 300 in progress |
||||
04/07/2018, 03:46 PM | #49 |
Registered Member
Join Date: Aug 2009
Location: Minooka Il
Posts: 912
|
Jimmy,
The way copps explained the the kydex is basically like cutting drywall. Measure the sides, score it with a razorblade, snap it, and you have clean edges. He only mentions bowing it to get around his colonies. He also uses magnets to keep in place. Once I have my 400 going I'm going to try it out. As far as the exhaust fan , no I do not use one. However I'm a service fitter that's been doing commercial/industrial HVAC for 20 years. I have seen people trying to use exhaust fans for temp/ humidity in computer rooms and typically it doesn't work well. I'd say the average humidity controlled rooms are around 35%. How big is the area you are trying to exhaust? And where is the stat located? |
04/07/2018, 04:03 PM | #50 |
Registered Member
Join Date: Aug 2009
Location: Minooka Il
Posts: 912
|
Is your ceiling is still open? By looking at your pics I'd guess those are two 3 ton condensers sitting outside. You could run a return duct in the space and use what you have for dehum. Living in Az I bet those things run a lot through the year. Then you could use the ex fan as a second stage.
|
Thread Tools | |
|
|