Reef Central Online Community

Go Back   Reef Central Online Community > Sponsor Forums > Tunze
Blogs FAQ Calendar Mark Forums Read

Notices

User Tag List

Reply
Thread Tools
Unread 11/17/2019, 05:57 AM   #1
mchammer
Registered Member
 
mchammer's Avatar
 
Join Date: Dec 2008
Location: Massachusetts
Posts: 293
Tunze 3155 ATO Problems

I just replaced my old Tunze osmolator with a new one yesterday and I am having problems with it. I setup the new one just like my previous one and plugged it in. No problems unit cycles and pump runs for 10 -20 seconds and then stops. The controller shows green light on water level, I comeback to my tank later that day and I hear the alarm going off and the water level is too high. I siphoned off the excess water and everything looks good again but when the water level in the sump dips below the sensor my Tunze over fills again. Can anyone help me with this problem?


mchammer is offline   Reply With Quote
Unread 11/17/2019, 07:08 PM   #2
dwsindy
Premium Member
 
dwsindy's Avatar
 
Join Date: Dec 2004
Location: Indianapolis
Posts: 218
Following this one as I am having the same problem.


dwsindy is offline   Reply With Quote
Unread 11/18/2019, 09:47 AM   #3
rvitko
RC Sponsor
 
rvitko's Avatar
 
Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
This tends to be the norm when they are new. The main reason is that new plastic is a bubble magnet and the optic sensor only detects air vs water and does not differentiate between bubbles and being dry. This tends to resolve itself after a few days, the plastic gets coated by a biofilm that reduces the attraction of bubbles. I would double check the following points though and another culprit can be infrared light from grow lights on a refugium.


1) A siphon, if it is a siphon the issue will be seemingly random, it will tend to only occur when the reservoir is full and the water will fill to a level possibly above or just below the float. Siphon situation 3 is the most probable cause but note as shown in 4 that a
loop will not solve it, the end of the hose must always terminate above the reservoir water level.

Siphon-Situations-688x459.png

2) A sensor issue. The first test is to use the self diagnostic test on the Osmolator to verify the sensor is in working order.

1) With the sensor completely wiped dry, plug in the controller. The sensor MUST be clean and dry for this test to work, a wet or dirty sensor will always fail.
2) All 4 lights will flash and it will beep, a single light will show for a couple seconds and then the normal 15-20 second pump run at startup will begin.
3) This light that is on a couple seconds is the optic sensor status, green means pass, yellow means it is marginal, red means it failed.

Assuming it passes the self test the issue is bubbles, optic sensors work by detecting the refraction of air vs water and make no differentiation between a bubble or being dry. The most overlooked source of bubbles is placing the top off hose in the vicinity of the sensors, the incoming splash will introduce bubbles and cause a fill. The hose can be routed to any area of the sump or main tank, and the optic sensor must be in a calm and bubble free area. A definitive test to verify bubbles are the cause is if you can catch it in the act of an overfill and wipe your finger across the sensor and filling stops within 5 seconds, the cause was bubbles.

3) There is a 3rd possibility but this is relatively obscure and only will apply to tanks under 50 gallons or due to a misunderstanding of how the Osmolator works. The Osmolator has timed functions in addition to sensor controlled functions and for the first 25-30 seconds it is not actually detecting water levels and is instead running a series of self diagnostic tests. The pump will always run for 15-20 seconds when you first power it up, this is so the installer can verify the pump is operational and the pump and tubing are primed and ready to fill. Also, the Osmolator always waits 5 seconds to fill to account for waves and surface movement and overfills for 5 seconds so the pump is cycled on less often. If the tank is under 50 gallons you need to open the controller and reduce the pump speed to “nano” and if it is under 30, an additional restriction such as a drip irrigation valve might be needed, this will reduce the amount of water added by these timed sequences to avoid raising the float.


__________________
Roger Vitko
Tunze USA

"He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!"

Current Tank Info: 210 gallon planted tank with Altum Angelfish
rvitko is offline   Reply With Quote
Unread 11/18/2019, 10:55 AM   #4
mchammer
Registered Member
 
mchammer's Avatar
 
Join Date: Dec 2008
Location: Massachusetts
Posts: 293
Update:

I wiped the sensor and it appears to be working properly. I did open the case and turn the flow down to nano before I wiped the sensor thinking it was filling the sump too fast and causing the problem. I have a 120 gallon tank and 40 gallon sump, should I readjust the flow setting? If so where should I put it?

Thank you for the quick reply Roger.


mchammer is offline   Reply With Quote
Unread 11/18/2019, 11:01 AM   #5
mchammer
Registered Member
 
mchammer's Avatar
 
Join Date: Dec 2008
Location: Massachusetts
Posts: 293
I mentioned this new Tunze ATO replaced an older one, I was wondering if my old ATO can be repaired and used as a backup. The plug and receptor for the plug is corroded on the inside.

Thanks


mchammer is offline   Reply With Quote
Unread 11/18/2019, 12:03 PM   #6
rvitko
RC Sponsor
 
rvitko's Avatar
 
Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
For that size tank I would generally be somewhere between 10-12 o clock for pump speed, 12 o clock is the factory setting.


__________________
Roger Vitko
Tunze USA

"He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!"

Current Tank Info: 210 gallon planted tank with Altum Angelfish
rvitko is offline   Reply With Quote
Unread 11/18/2019, 12:03 PM   #7
rvitko
RC Sponsor
 
rvitko's Avatar
 
Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
I can possibly repair the old one, I would have to see it and it would only be feasible if newer than late 2011.


__________________
Roger Vitko
Tunze USA

"He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!"

Current Tank Info: 210 gallon planted tank with Altum Angelfish
rvitko is offline   Reply With Quote
Unread 12/09/2019, 03:31 PM   #8
QuickxSilver
Registered Member
 
Join Date: Sep 2019
Posts: 19
I'm having the same issue, will give this a try and see if it fixes it.


QuickxSilver is offline   Reply With Quote
Unread 12/26/2019, 09:54 PM   #9
pinoy.reef2016
Registered Member
 
pinoy.reef2016's Avatar
 
Join Date: Dec 2019
Posts: 3
Tunze 3155 Start-up error

I just bought a used Tunze 3155 and upon set-up it failed. Seller told me that it was perfectly working before he shutdown his tank and removed all the equipment.

2 LEDs - the Too high and Too low lights are flashing at the same time with a continuous beeping alarm. I opened the controller but there is no apparent water damage. I also cleaned the solenoid connections and checked the power adaptor (correct one). Not sure what is wrong. Please assist. Is Roger Vitko onboard? Thanks!


pinoy.reef2016 is offline   Reply With Quote
Unread 12/27/2019, 08:26 AM   #10
rvitko
RC Sponsor
 
rvitko's Avatar
 
Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
This is the water damage indicator, usually the damage is invisible as the usual issue is a power supply tip was plugged in while wet and the damage is under the power socket on the board. I would send in the controller and power supply for repair.


__________________
Roger Vitko
Tunze USA

"He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!"

Current Tank Info: 210 gallon planted tank with Altum Angelfish
rvitko is offline   Reply With Quote
Unread 12/27/2019, 09:27 AM   #11
pinoy.reef2016
Registered Member
 
pinoy.reef2016's Avatar
 
Join Date: Dec 2019
Posts: 3
Thank you for the prompt response Roger! Will send the controller and the power supply. I got your address as:
Tunze USA
305 Victor St
Austin, TX 78753


pinoy.reef2016 is offline   Reply With Quote
Unread 12/27/2019, 02:38 PM   #12
rvitko
RC Sponsor
 
rvitko's Avatar
 
Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
That is correct.


__________________
Roger Vitko
Tunze USA

"He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!"

Current Tank Info: 210 gallon planted tank with Altum Angelfish
rvitko is offline   Reply With Quote
Unread 01/08/2020, 11:24 PM   #13
pinoy.reef2016
Registered Member
 
pinoy.reef2016's Avatar
 
Join Date: Dec 2019
Posts: 3
Just received the 3155 this afternoon, tested it and it works! Thank you again Roger! You're the BEST!


pinoy.reef2016 is offline   Reply With Quote
Unread 01/09/2020, 08:37 AM   #14
rvitko
RC Sponsor
 
rvitko's Avatar
 
Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
Thank you!


__________________
Roger Vitko
Tunze USA

"He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!"

Current Tank Info: 210 gallon planted tank with Altum Angelfish
rvitko is offline   Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



All times are GMT -6. The time now is 02:20 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2024 Axivo Inc.
Use of this web site is subject to the terms and conditions described in the user agreement.
Reef CentralTM Reef Central, LLC. Copyright ©1999-2022
User Alert System provided by Advanced User Tagging v3.3.0 (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.